• NEOQUIM - OLD OLD envejecedor de mármol

    OLD

    Aging treatment for marble and polished stone.
    • Professional chemical aging.
    • Suitable for indoor and outdoor use.
    • Provides anti-slip protection. .
    • High performance.
    • Irreversible.
    Old is a chemical treatment specially designed to age in a fast and effective manner all kinds of marbles and natural stones susceptible to chemical attack by acids, such as: limestone, sandstone, shale, etc. Once applied, OLD chemically modifies the surface so that the treated stone remains with a surface roughness identical to that caused by the passage of time and meteorological agents on materials exposed to the weather. Due to its optimal formulation, high quality and high effectiveness, OLD also generates an anti-slip effect on the applied stones. This causes the treated coating to lose surface gloss and to acquire roughness, increasing the surface slipperiness coefficient. Based on its excellent properties and excellent results obtained on a large number of surfaces, they make OLD a very useful treatment for stairs, ramps and any access with this type of pavement that poses a slipping problem or that you want to give it a decorative aged appearance with permanent durability. Treatment with OLD is irreversible, so the surface can only be restored to its original state by polishing.

    Application Areas

    Old can be used on all kinds of marble surfaces or limestone derivatives where you want to give an aging look or a anti-slip finish. In addition, OLD can be used in restoration work to match areas where new pieces have been placed next to old pieces.

    Mode of Application

    Depending on the degree of attack required, it can be used undiluted or diluted. Before applying OLD, it is recommended to perform a preliminary test to adjust the required attack rate by modifying the dilution or attack time.

    The following steps are recommended to apply OLD:

    •  Initially, surfaces adjacent to the part must be protected to prevent possible splash damage, mainly if they are metallic.
    •  Then apply a small amount of OLD using a brush, roller or spray.
    • Then, leave on for 5 – 15 minutes, depending on the degree of attack required, (which depends on the type of material).
    • Finally, wash with plenty of water and let dry.

    Format

    • Plastic containers of 5, 10 and 30 litres.
    Details
  • Tratamiento antideslizante - Neoquim NEOQUIM - ANTIDESLIZANTE

    ANTI-SLIP

    Permanent anti-slip action for vitrified surfaces.
    • Ready to use.
    • Permanent action.
    • Quick and easy to apply.
    • It does not change the colour.
    • Suitable for indoor and outdoor use.
    Anti-slip is a chemical formulated with inorganic acids, wetting agents and reactive substances, which chemically transform the surface on which it is applied, thanks to a chemo-mechanical procedure, reducing its slipperiness in wet conditions. In this way, anti-slip treated surfaces increase their slip resistance in wet conditions, this treatment resulting more economical than the installation of a new non-slip floor. In addition, since Anti-slip chemically and irreversibly transforms the surface, its durability is extremely high, contrary to what happens when applying products based on resins and developed for the same purpose. Therefore, Anti-slip is especially recommended for use on vitrified mineral surfaces, enamelled or highly polished mineral surfaces, such as: ceramic, porcelain, stoneware, mosaic, polished concrete, terrazzo tile, limestone… etc. Anti-slip does not change the colour of treated surfaces and is suitable for both exterior and interior. The product can also be reapplied to surfaces on which it has been previously used. Optimal performance and commissioning. Anti-slip is applied and reacts quickly, so Anti-slip treated pavements have a quick service start.

    Application Areas

    Anti-slip is effective on most surfaces used in construction, such as: mortars, terrazzo, limestone, stoneware and porcelain tiles, and even on vitrified and enamelled surfaces, such as bathtubs, shower trays… etc. Therefore, it is especially recommended to be applied in moderate to heavy transit areas where slippage wants to be avoided. For example:
    • Indoor and outdoor pavements.
    • Shower trays or enamelled baths
    • Banks.
    • Airports.
    • Schools.
    • Public buildings
    • Etc.

    Mode of Application

    Anti-slip is a ready to use product, so it does not need to be diluted before applying. Before applying the anti-slip treatment it is strongly recommended to perform a test to check the final surface result and appearance and to adjust the product drying time.
    1. Initially apply the product to the surface by spraying or mopping.
    2. Then let it dry for the estimated time in the previous test, (usually a contact time of 5-10 minutes is sufficient). To achieve an optimal homogeneity in the surface finish, it is recommended to work with 15-20 m2 areas.
    3. Finally, rinse with plenty of water until the surface has a pH= 7-8.

    Format

    • Plastic container of 0.5 and 1 L.
    • Industrial packaging of 5, 30 and 60 L.
    Details
  • NEOQUIM - FANG FANG Protector y avivador

    FANG

    Special stain protector for burnt clay and terracotta.
    • Suitable for indoor and outdoor use.
    • Prevents the appearance of stains.
    • Enhances the tone of the surface.
    • High durability.
    • It does not form a film.
    Fang is a solvent-based stain protector and colour reviver for floors and clay coatings, such as: burnt clay, terracotta or Catalan stoneware, among others, designed so that treated surfaces do not absorb water, oils and other liquids by capillarity. In this way, the treatment of these with Fang gives them a complete protection against humidity and oily spots, while increasing and restoring their original tone. Fang does not use resins to achieve this effect, so the treated surfaces maintain their natural transpiration and maintain their original texture. It does not add shine, keeping the original anti-slip features intact. Also, since it does not contain resins in its composition, it does not crack, becomes yellowish or physically deteriorates with the passage of time, being especially durable against UV radiation. Fang also has a low viscosity, which together with its 100% solvent composition, allows a high degree of penetration and protection in both low and high absorption substrates, whether in vertical or horizontal applications. Due to the water repellent and oleophobic properties, Fang delays, on the one hand, the appearance of problems caused by water, such as: efflorescence, moulds or verdigris and, on the other hand, facilitates the cleaning of all kinds of vegetable oils and grease stains.

    Application Areas

    Fang is suitable for use in any clay, terracotta, rustic stoneware, cladding tile, ceramic flooring and, in general, absorbent clay surfaces, both vertical and horizontal.

    Mode of Application

    FANG is a ready to use product, so it does not need to be diluted before applying. Before applying Fang, make sure that the surface to be treated is completely clean of dust, efflorescence, mould, greases… etc. The surface must also be completely dry and with a residual humidity of less than 5%. If the surface appears whitish due to the presence of saline efflorescence, we recommend to clean it before with Limfa F. If it has been previously waxed, all wax must be removed using Neogras 14.

    After cleaning the surface:

    1.  Apply the product with a brush, short hair roller or dry cloth and spread evenly across the entire surface.
    2.  Then let the product dry, re-applying a new coating after 30-60 minutes if necessary. The surface will be completely dry and protected after 6 hours. On low absorption surfaces, it may be necessary to remove excess product by wiping with a clean, dry cloth.

    Format

    • Metal containers of 1, 5, 10 and 30 litres.
    Details
  • HIDROSOL AQUO PLUS

    Colourless water based water-repellent with for.
    • Water based.
    • High water repellent power.
    • It does not alter the tone.
    •  Reduces dirt adhesion.
    •  Vapour breathable.
    Hidrosol Aquo Plus is a water resistant product ready to use for façades made of concrete, mortar, masonry, brick, natural stone or fibre cement, among others, formulated with organosilic compounds of the latest technology, emulsified in water. hanks to its high concentration of active ingredients, Hidrosol Aquo Plus provides a high water-repellent capacity and an optimal pearl effect, without altering the original tone of the surface or forming a film. It prevents water penetration into the surface while allowing its breathability and reduces the formation of efflorescence, moss and lichens, maintaining the aesthetic conditions of the wall finish. Hidrosol Aquo Plus can be applied both indoors and outdoors since it does not emit any solvent/odour and is totally UV resistant.

    Application Areas

    This product is especially suitable for water-proofing all types of vertical construction surfaces or on surfaces with slopes of more than 5 degrees of inclination, such as: Natural stone, caravista brick, concrete, mortar, plaster, fibre cement, roof tile…

    Mode of Application

    Before applying Hidrosol Aquo Plus, it must be checked that the surface is fully hardened and set in case of new constructions, totally dry, free of dust, dirt, oils, efflorescence and a temperature between 5 and 35 °C It can be applied with an airless sprayer, brush or roller, applying two layers of product using the “wet on wet” methodology. To do this, apply the second layer of product while the first layer is still humid. Hidrosol Aquo Plus is not suitable for horizontal surfaces, nor for being coated with cement or lime based paints.

    Format

    • Plastic containers of 1, 5, 10 and 30 litres.
    WATCH VIDEO.
    Details
  • HIDROSOL MG

    Wet look water repellent for low porous surfaces.
    • Protects against problems caused by water.
    • It enhances the tone of the stone.
    • Improves wear resistance.
    • Allows the surface to breathe.
    • Ready to use.
    Hidrosol mg is a water-repellent product, based on siloxanes and polysiloxanes in a solvent base, specifically created to protect all types of absorbent surfaces against problems caused by water, such as humidity, salt efflorescence, moulds and verdigris growth or the appearance of frost cracks, among others. In addition, Hidrosol MG positively contributes to reduce the heat transmission coefficient of the treated wall, improving its thermal insulation capabilities. Its well thought out resin-free composition provides a completely colourless and non-gloss water barrier, keeping the surface breathability intact. Once the product has been absorbed by the surface, Hidrosol MG enhances its natural tone, giving it a moist appearance. This gives the surfaces a completely rejuvenated appearance with more vivid colours. Hidrosol MG is suitable for all types of materials and absorbent surfaces, both vertical and horizontal with a slight slope (>3%), which together with its optimal resistance to abrasion and UV rays, has excellent durability. In addition, since it does not contain any resins in its composition, it does not yellow, crack or peel over time and is 100% trafficable.

    Application Areas

    Hidrosol mg is the ideal product to use when it is necessary to protect low porosity surfaces against the action of water and give them a wet appearance simultaneously. For example: polished marble and granite surfaces, slate, unglazed ceramic surfaces…etc.

    Mode of Application

    HYDROSOL MG is a ready to use product, so it does not need to be diluted before applying. Before applying Hidrosol MG, the surface must be completely clean, hardened and perfectly dry. In addition, it must be absorbent, otherwise the treatment will not be effective, generating a sticky surface. Then apply Hydrosol MG on the surface until it is fully saturated. This can be done by using: short hair roller, brush or low pressure spray. Then, let the product be absorbed by the treated stone for 30 minutes. If after that time Hydrosol MG has not completely penetrated, remove the excess with the help of a cloth / absorbent material. Finally, let the treatment dry completely. After 24 hours the product is 100% effective. It is recommended to protect against condensation or rain within the first 24 hours of application.

    Format

    • Metal containers of 1, 5, and 10 litres.
    • Plastic container of 30 litres.
    Details
  • HIDROSOL STONE PLUS BLACK

    Water repellent – colour enhancer for granites and black marbles.
    • High concentration
    • Intensifies and restores the original black colour of the stone.
    • Optimal water-repellent protection.
    •  Excellent durability.
    Hidrosol Stone Plus Black is a solvent based water repellent based on siloxanes and polysiloxanes specifically designed to be applied on black marble and granite surfaces.

    Hidrosol Stone Plus Black has a dual mode of action:

    1.  It provides hydrophobic properties to the surfaces where it is applied. In this manner, the treated stone does not absorb water, reducing the problems caused by the same such as: appearance of white spots, saline efflorescence, loss of gloss, oxidation… etc. This mode of action is obtained thanks to its silicon-based compounds, high hydrophobic capacity and excellent resistance to wear and light.
    2. It intensifies and restores the original black colour of the stone, giving it a high durability deep black hue that conceals small imperfections or streaks in granites and marbles bringing back their original appearance. Its extremely fine pigments penetrate the stone and improve the visual characteristics of the surface thanks to their high opacity.
    Hidrosol Stone Plus Black does not use resins or polymers in its composition, so it acts without altering the surface gloss. This fact makes it especially useful on surfaces with honed or flamed finishes.

    Application Areas

    Hidrosol Stone Plus Black is suitable to be applied in all types of natural black stone, both vertical and horizontal, such as:
    • Floors.
    • Countertops or tables
    • Decorative elements
    • Etc.

    Mode of Application

    Hidrosol Stone Plus Black is a ready to use product, so it does not need to be diluted before its application. Before applying Hidrosol Stone Plus Black, the surface must be completely clean, hardened and perfectly dry. In addition, it must be absorbent, otherwise the treatment will not be effective, generating a sticky surface. Apply Stone Plus Black on the surface until it is fully saturated. It can be applied with: a short hair roller, brush or low pressure spray, it is recommended to apply it following the “wet on wet” technique in two crossed layers. Then, let the product be absorbed by the stone for 30 minutes. If after said time Hidrosol Stone Plus Black has not completely penetrated, remove the excess with the help of a cloth / absorbent material, rubbing gently with circular movements Finally, let the treatment dry completely. After 24 hours the product is 100% effective.

    Format

    • Metal containers of 0.5 litres+box, 1, 5 and 10 litres.
    • Plastic container of 30 litres.
    Details
  • HIDROSOL STONE PLUS

    Brightener, protective and water repellent for synthetic materials.
    • Protects against water.
    • Improves gloss and enhances the colour.
    • For quartz and non-absorbent synthetics.
    • Makes cleaning easy.
    Hidrosol Stone Plus is a brightener, protector and colour intensifier specially developed for non-absorbent surfaces such as synthetics, quartz agglomerates or natural non-porous or highly polished stone. It is based on non-toxic wetting agents, solvents and non-toxic colour enhancers and protectants. Hidrosol Stone Plus, boosts the gloss and enhances the natural colour of the treated surfaces after its application, generating a thin film that is completely transparent and colourless providing high protection against water stains. Treated surfaces also have a soft feel and are easier to clean. Thanks to these features, Hidrosol Stone Plus is the most recommended product to be used in cases where a typical water repellent (designed for absorbent surfaces) cannot be used. Suitable for both professional and home use. Hidrosol Stone Plus can be used by all types of users for its ease of use. Hidrosol Stone Plus can be applied regularly to keep the surface gloss intact.

    Application Areas

    Hidrosol Stone Plus is intended to provide protection, enhance the tone and increase the gloss of non-absorbent and/or polished surfaces, such as technological quartz, marble, granite, glazed ceramics, among others, on all types of surfaces and uses:
    • kitchen and bathroom worktops,.
    • Tables.
    • Decorative elements,.
    • Bar tops in businesses,.
    • Vertical claddings,.
    • Etc.

    Mode of Application

    Hidrosol Stone Plus is a ready to use product, so it does not need to be diluted before its application. Before applying, the surface must be clean and completely dry.

    Then:

    1. Moisten a microfibre cloth with Hidrosol Stone Plus.
    2. Spread the product evenly over the entire surface to be treated.
    3. Leave it on for 10- 15 minutes.
    4. Remove excess product with a dry microfibre cloth.
    5. Rub the surface, preferably with circular movements, until the desired gloss is obtained.

    Format

    • Metal containers of 0.5 litres+box, 1, 5 and 10 litres.
    • Plastic container of 30 litres.
    Details
  • LIMFA F

    Limfa F is a non-oxidizing safe acid cleaner, formulated with specific inorganic acids and high quality moisturizing additives that make this product a powerful cleaner for cement, salts and encrusted dirt on all types of acid-resistant surfaces. Limfa F removes traces of lime, cement, efflorescence, rust, saltpetre and other impurities that commonly used alkaline cleaners do not eliminate, both on façades and in rustic floors.
    Details
  • NEOQUIM - LIMFA GEL LIMFA GEL producto

    LIMFA GEL

    Special cleaner and descaler gel for vertical surfaces. 
    • Specially designed for pool cleaning
    • Concentrated product.
    • Easy application.
    • Fast clarifier.
    • Acid nature.
    Limfa Gel is a professional grade cleaner and descaler gel, of an acid nature, designed to clean and remove calcareous incrustations, residues and mineral sediments that accumulate and adhere to surfaces that are in permanent contact with water or contain large amounts of moisture. Its careful composition, based on inorganic acids, surfactants, corrosion inhibitors and thixotropic agents, transforms the insoluble and highly encrusted salts into easily washable chemical compounds, disintegrating even the most adhered encrustations without affecting epoxy resin and elastic gaskets or metallic decorative elements. Limfa Gel has a high viscosity texture, allowing high contact times on vertical surfaces, ensuring effective cleaning with the minimum amount of product. Thanks to this characteristic, Limfa Gel is especially recommended to clean swimming pools waterline, since it easily removes dirt and encrustations from edges and walls. The cleaning and descaling action of Limfa Gel also makes it suitable to remove mould and verdigris that accumulates in the joints. Limfa Gel is suitable to be used on all types of surfaces such as: glass, porcelain tiles, stoneware, glass mosaic, chlorinated rubber paint, etc., and, in short, on any surface not susceptible to attack by products based on inorganic acids.

    Application Areas

    Cleaning lime residues and adhered sediments on vertical surfaces such as walls, façades and swimming pools.

    Mode of Application

    Limfa Gel is a concentrated product, so it must be diluted before use. Protective gloves are recommended for its handling and use. The following indications must be followed for its use: 
    1.  Slightly moisten the surface to be cleaned
    2.  Apply the product to the surface to be cleaned using a brush or roller. Depending on the amount of dirt to be removed, Limfa Gel can be used pure or diluted with up to 5 parts of water, (1 L of Limfa Gel + 5 L of water).
    3.  Allow it to work for a few minutes, rubbing if necessary with a bristle brush.
    4.  Rinse abundantly with water, preferably with pressurised water to finish.

    Format

    • Plastic containers of 1, 5, 10 and 60 litres.
    Details
  • LINKER STONE

    Two-component gravel adhesive for tree surrounds.
    • Good weather resistance.
    • Excellent adhesion and bonding.
    • Allows water to drain.
    • Easy application.
    Linker Stone is a two-component adhesive, based on solvent free epoxy resins and high cohesion capacity, specifically designed to bond, fix and compacting decorative gravel. Thanks to its optimal formulation, its high quality and its optimum mechanical and weather resistance, Linker Stone, allows the chemical bonding of all types of aggregates used in the construction of roads, tree surrounds or decorative gardens, among others, allowing pedestrians and light traffic to circulate without the gravel coming loose. Linker Stone has no film properties, so the aggregate surfaces retain their liquid permeability capacity and allow the substrate to breathe while allowing moisture retention, optimizing the irrigation water for gardens and facilities.

    Application Areas

    Linker Stone is suitable for use in all work where a gravel adhesive product with high adhesion, durability and performance is required. By its characteristics, Linker Stone can be used in: tree surrounds, gardens and decorative areas, roads, walkways, traffic islands, roundabouts, etc., and, in short, in any area that requires a solid and resistant base to pedestrian traffic without the gravel used coming loose.

    Mode of Application

    1.  Stir components A and B separately using a stirrer fitted with a mixing rod. The stirring must be performed at low revolutions to prevent air occlusion.
    2.  Mix component A with component B using the ratio 2:1, respectively. Stir the mixture for 2 minutes at low revolutions.
    3.  After mixing, add Linker Stone to the gravel and shake the mixture for a few minutes until the gravel is fully impregnated with the product. The Linker Stone dosage should be 20-40 grams of A+B component mixture per kg of gravel, according to its size.
    4.  Extend the gravel and compact it to obtain a fully firm surface.
    Linker Stone can also be applied by spraying to harden and repair previously compacted gravel surfaces. To do this, it is recommended to make the mixture of components A and B according to the above instructions and add 20-40% Disol to the mixture. Then spray the Linker Stone mixture onto the surface to be hardened/repaired. The performance of the mix applied has to be adjusted on a case-by-case basis.

    Format

    • Metal container: 1.5 (1+0.5kg), 6 kg (4+2) y 15 kg (10+5).
    Details
  • NEOQUIM - NEODECAPINT CLEANER NEODECAPINT CLEANER

    NEODECAPINT CLEANER

    Neodecapint Cleaner is a paint stripper, based on non-chlorinated solvents and powerful, highly effective surfactants, specifically designed to dissolve and remove polymers from old and dried resins and paints from various surfaces in a few minutes. These qualities make it especially suitable for cleaning all types of paint, varnish or enamel adhered to materials commonly used in construction, such as: brick, plaster, unpolished marble, granite or wood, among others. Neodecapint Cleaner is effective with synthetic, cellulosic, siliconised, nitro or emulsion plastic paints, as well as in the removal of resins, lacquers and glues on any washable hard surface. It is also suitable to clean paint tools such as: rollers and any type of paint brushes other than rubber or nylon. Its gel texture allows for convenient application on vertical surfaces increasing contact times and improving product efficiency. For plastic surfaces, it is recommended to carry out a preliminary test to confirm that it resists the paint stripper action, otherwise, Neodecapint Soft is recommended (special for delicate surfaces).

    Application Areas

    Neodecapint Cleaner is to be used in situations where the use of an strong paint stripper suitable for use on construction surfaces is required, such as:
    • Brick.
    • Granite.
    • Marble.
    • Plaster.
    • Mortar.
    • Wood.
    • Etc.

    Mode of Application

    Neodecapint Cleaner is a ready to use product, therefore it does not need to be diluted before use. It is always recommended to shake the contents of the container until it is fully homogenised.
    1.  Apply spreading with a paint brush over the surface to be stripped.
    2.  Leave on for 10-15 minutes for the active substances to remove the paint.
    3.  Rinse with pressurized water, preferably hot.

    Watch product video Neodecapint Cleaner

    Details
  • NEODECAPINT ECO GEL

    Stripping gel for low/non-porous surfaces.
    • Stripping gel.
    • Without chlorinated solvents.
    • Fast and effective action.
    • Multisurface.
    •  Quick drying.
    Neodecapint Eco Gel is a stripping gel free of chlorinated solvents, designed for the removal of varnishes, glues, lacquers, paints and even asphalt remains on low or non-porous surfaces. With medium viscosity, giving it an optimal adhesion on the coating to be stripped, so it is suitable for use on both vertical and horizontal surfaces. In addition, its special composition combines two different modes of action:
    •  This stripper effectively dissolves polymers from resins and paints in a few minutes, softening the coating and allowing it to be easily removable.
    •  It also passes through the coating and reaches the surface. At this point, it eliminates the adhesion of the coating, allowing it to peel off more easily.
    This mode of action allows the process to be fully effective and fast without having to resort to highly toxic solvent-based products such as dichloromethane. Neodecapint Eco gel can be used on all types of surfaces, mainly vertical (except for plastics), since it does not chemically affect them. Therefore, it can be used on urban furniture of different materials, metals, wood, polished natural stone surfaces, etc.

    Application Areas

    It is suitable for the removal of all types of coatings in:
    • Polished natural stone
    • Porcelain materials
    • Wood or metals varnished or lacquered
    • Aluminium
    • Etc.

    Mode of Application

    Neodecapint Eco Gel is a ready to use product, therefore it does not require dilution before use.
    1. Apply on the surface to be stripped, ensuring to spread a layer of 300-400 microns of the product.
    2. Leave the product on for a few minutes. On non-porous surfaces it will be observed that the paint begins to deteriorate, losing gloss and surface wrinkles appear.
    3.  Then remove the stripped paint. Depending on the type of surface it can be performed with the aid of a spatula or scraper, or with a hydro-cleaner.
    4. Finally, rinse the surface with a cloth dampened with water.

    Format

    • Metallic container of: 1, 5 and 10 litres.
    • Plastic container of: 30 litres.
    Details
  • NEOQUIM - NEODECAPINT ROTU NEODECAPINT ROTU

    NEODECAPINT ROTU

    Multisurface marker pen graffiti remover.
    • Easily removes graffiti and marker shadows.
    • Fast action.
    • Suitable for spraying.
    • Multisurface.
    Neodecapint Rotu is an ink and graffiti stripper-remover based on a synergistic mixture of solvents and surfactants, specially developed for the elimination of marker pens graffiti made on all types of washable, low-porous surfaces. Neodecapint Rotu has a fast dissolving action on inks and pigments, so its action is highly effective. In addition, its low viscosity also allows its direct use by spraying, optimizing cleaning times and economising on the product. This property also optimizes its surface penetration capability, eliminating even the most difficult to remove shadows with a single application. Given its special composition, Neodecapint Rotu is effective on all types of polished, varnished or enamelled surfaces, such as: polished granite, glass, lacquered wood, painted metals, etc. Also, with short application times, it does not affect the surface under the graffiti, avoiding the need to repaint the surface after the graffiti has been removed.

    Application Areas

    Neodecapint Rotu is to be used for the removal of graffiti made with any kind of marker on hard surfaces with low porosity or non-porous, such as: granite or polished marble, lacquered or varnished wood, glass, painted metals, etc. It is therefore particularly recommended for use on urban furniture, playgrounds, metal doors and letter boxes, façades, etc.

    Mode of Application

    Neodecapint Rotu is supplied ready to use, so no dilution is necessary at all.
    •  Apply Neodecapint Rotu on the graffiti to be removed. It can be applied either by direct spraying or by impregnating a cloth with the product.
    • Then, gently rub and let the product work for a few minutes.
    • Finally, rinse with plenty of water to obtain a completely clean surface. This procedure is most effective if pressurized water is used, preferably hot.
    • Repeat the operation if necessary.

    Format

    • Metal container: 1 litre (boxes with 8 units).
    • Industrial packaging: 5, 25 and 50 litres.
    Details
  • NEOQUIM - NEODECAPINT SOMBRAS FORTE NEODECAPINT SOMBRAS FORTE

    NEODECAPINT SOMBRAS FORTE

    Graffiti shadow remover for porous surfaces.
    • High effectiveness.
    • Removes graffiti from marker pens and graffiti shadows.
    • Fast action.
    • Sprayable.
    Neodecapint Sombras Forte is a stripper-cleaner specially designed for the removal of shadows and graffiti traces made on medium to high porosity surfaces, being the perfect complement to finish the cleaning of difficult graffiti that has previously been stripped leaving traces or shadows. Neodecapint Sombras Forte combines solvents with high disintegrating capacity, paint digesting alkalis and surfactants that improve product performance. This combination of ingredients dissolves the remaining pigments of the before cleaned graffiti, eliminating shadows in a few minutes, resulting in a complete cleaning of the treated surface. This special composition allows Neodecapint Sombras Forte to be used on all types of surfaces commonly used in construction, such as: concrete, caravista rustic brick, marble, granite, slate, sandstone or wood among others. Neodecapint Sombras Forte has a low viscosity texture, so it can be applied by spraying as well as with a brush or roller. This application method allows for higher working speed, optimizing cleaning times and reducing chemical consumption.

    Application Areas

    Neodecapint Sombras Forte is to be used as a shadow cleaning supplement after the removal of graffiti on very porous surfaces or with graffiti heavily impregnated into the surface. For example, after using Neodecapint Cleaner on brick or concrete surfaces.

    Mode of Application

    Neodecapint Sombras Forte is a ready to use product.
    1. Slightly moisten the area to be cleaned, then apply Neodecapint Sombras Forte.
    2. Leave it on for 5 - 30 minutes without allowing the product to dry on the surface, rubbing lightly with a bristle brush.
    3. Rinse preferably with plenty of hot pressurized water.

    Format

    • Plastic container with degasifier cap: 1 litre.
    • Industrial packaging: 5, 30 and 60 litres.
    Details
  • NEOQUIM - NEODECAPINT TOTAL neodecapint total producto

    NEODECAPINT TOTAL

    Multipurpose paint stripper for low/non-porous surfaces. Neodecapint Total is a low viscosity paint stripper free of chlorinated solvents designed for the removal of varnishes, glues, lacquers, paints and even asphalt remains on low or non-porous surfaces. Neodecapint Total has a medium viscosity, giving it an optimal adhesion on the coating to be stripped, so it is suitable to be used on both vertical and horizontal surfaces. In addition, its special composition combines two different modes of action:
    • On the one hand, this paint stripper effectively dissolves polymers from resins and paints in a few minutes, softening the coating and allowing it to be easily removable
    •  On the other hand, Neodecapint Total passes through the coating and reaches the base of the same on the surface. At this point, it eliminates the adhesion of the coating, allowing it to peel off more easily.
    This mode of action allows the process to be fully effective and fast without having to resort to highly toxic solvent-based products such as dichloromethane. Neodecapint Total can be used on all types of surfaces, (except for plastics), since it does not chemically affect them. Therefore, it can be used on urban furniture of different materials, metals, wood, polished natural stone surfaces, etc.

    Application Areas

    Neodecapint Total is suitable for the removal of all types of coatings in:
    • Polished natural stone.
    • Porcelain materials.
    • Wood or metals varnished or lacquered.
    • Aluminium.
    • Etc.

    Mode of Application

    Neodecapint Total is a ready to use product, therefore it does not require dilution before use.
    1.  Apply Neodecapint Total on the surface to be stripped, ensuring to spread a layer of 300-400 microns of the product.
    2.  Leave the product on for a few minutes. On non-porous surfaces it will be observed that the paint begins to deteriorate, losing gloss and wrinkles appear on the surface.
    3. Then remove the stripped paint. Depending on the type of surface it can be performed with the aid of a spatula or scraper, or with a hydro-cleaner.
    4. Finally, rinse the surface with a cloth dampened with water.

    Format

    • Plastic container of 0.5L+Sprayer.
    • Industrial packaging: 5, 10 and 30 litres.
    Details
  • NEOLATEX ELASTIC

    Neolatex Elastic is a liquid additive based on a careful selection of last generation modified acrylic resins, developed to be added to mortars and mastics during the mixing phase, generating materials with high flexibility and a low tendency to crack formation.   Also, the addition of Neolatex Elastic improves the following properties:
    • Adherence: Neolatex Elastic gives the mortar/putty a better "gripping" capacity on the surface.
    • Workability: Mortars and mastics with Neolatex Elastic additive are easier to spread and smooth, avoiding the operator fatigue.
    • Waterproofing: The addition of Neolatex Elastic in the recommended proportions allows to obtain mortars totally waterproof, resisting even standing water and tiling.
    • Resistance to wear and cracking: Since Neolatex Elastic provides a high degree of flexibility to the mortar, it reduces its cracking during setting. In addition, its resistance to abrasion is strongly increased, resulting in more durable materials.
    • Carbonation resistance: Neolatex Elastic generates an internal network  that prevents the mobility of the salts contained in the mortar. This dramatically reduces the occurrence of saline efflorescence. This keeps the material clean and consolidated for longer.
    • Colour durability: In pigmented mortars, the addition of Neolatex Elastic maintains the colour of the material virtually unchanged.

    Application Areas

    Neolatex Elastic can be used in all types of mortars and mastics where increased durability and waterproofing properties are desired. For example, in the manufacture of: showers and baths bases, vertical surfaces with cracking tendency, waterproofing of lift shafts, generation of regularising and waterproofing layers of water tanks, pools or terraces, etc.  

    Mode of Application

    Neolatex Elastic is to be used in the mixing stage of the mortar or mastic, replacing part of the mixing water with Neolatex Elastic. For this:
    •  Add the mixing liquid to the concrete mixer or mixing container. As a mixing liquid, use a water mixture of: Neolatex elastic equal to 1:1 or 2:1. Dilutions above 3:1 (Water: Neolatex Elastic) are not recommended.
    •  Add the mortar / mastic and mix according to the mortar / mastic instructions.
    • Apply the mortar following the desired procedure. (For fully flexible layers it is recommended not to exceed 2 mm thickness).

    Format

    • Plastic container: 5, 30 and 60 litres.
    Details
  • OXICLEAN FERRO

    Oxiclean Ferro is a ready to use non-acid rust remover, specially developed to remove rust stains from all types of mineral surfaces in a quick and easy way. It is not based on acids and has a neutral pH, so Oxiclean Ferro can be used on delicate and polished mineral surfaces without affecting their gloss. Its high concentration allows to eliminate a large amount of rust using a minimum product dose, optimizing costs and storage. Oxiclean Ferro has an excellent penetration capacity, so it is also effective in removing surface rust in materials such as marble, cement, terrazzo or hydraulic tiles. Also, its low viscosity gel presentation allows its localized application, optimizing the cleaning process and product consumption. Oxiclean Ferro is suitable to be applied on all types of mineral surfaces, such as:
    • Marble.
    • Granite.
    • Natural stone.
    • Agglomerates.
    • Porcelain stoneware.
    • Ceramic.
    • Clay.
    • Cement.
    • Sandstone.
    • Limestone.
    • Etc.

    Format

    Containers of 125 ml and 0.5 L  
    Details
  • OXICLEAN LG

    Rust remover for non-limestone natural stone.
    • High concentration.
    • Suitable for vertical and horizontal surfaces.
    • Easy application.
    • Immediate results.
    • Special for non-polished surfaces.
    Oxiclean LG is a concentrated rust remover cleaner, based on a mixture of high-power inorganic acids, degreasing agents, surfactants and specific moisturisers, which remove all kinds of non-deep rust stains and calcareous incrustations in mineral materials such as granite, brick, concrete, tile or natural non-limestone stones, among others. Thanks to its components, Oxiclean LG reacts with iron oxide, which is insoluble in water, transforming it into soluble chemicals. This allows to remove the stains quickly and effortlessly. Just spray Oxiclean LG over the stain to be removed, let it act and rinse with water. Oxiclean LG also removes salts deposits, such as calcareous incrustations or efflorescence, by chemically decomposing them into CO2 and easily removable chemical derivatives by a light rinse. Formulated with moisturizers and surfactants, Oxiclean LG also removes pigment dirt, such as soot or pollution, as well as organic dirt, such as moss, lichen or verdigris, combining a detergent and rust remover action in a single product. Oxiclean LG, therefore, is especially suitable for deep cleaning in acid-resistant materials such as:
    • Granites.
    • Clays and porcelain tiles.
    • Etc.

    Application Areas

    Oxiclean LG is to be used when a strong product is required for a thorough cleaning of rust, salts or pollution stains on acid-resistant mineral surfaces. For example:
    • Floors or façades of brick,.
    • Granite.
    • Slate.
    • Natural non-limestone stones.
    • Etc.

    Mode of Application

    OXICLEAN LG is a concentrated product, so it must be diluted before use. The degree of dilution must be adapted to each particular cleaning and surface. As an orientation dosage, it can be diluted with up to 3 parts of water.

    The following indications must be followed for its use:

    1. Lightly moisten with water the surface to be cleaned.
    2. Apply Oxiclean LG, impregnating the surface with a brush or low pressure spray.
    3. Leave the product on for a few minutes. The reaction time may vary depending on the state of the surface. 2-3 minutes are usually sufficient for surface dirt and 15-20 minutes for rust and highly adhered or deep dirt such as rust spots.
    4. Scrub with a bristle brush if necessary.
    5. Rinse with plenty of water, preferably hot and pressurized.
    6. Reapply if dirt is persistent.

    Format

    • Plastic containers of 5, 10 and 10 litres.
    Details
  • PROTECTOR STONE AQUO

     
      • Stone Aquo Protector is an water based anti-stain protector, formulated with high-quality oil-repellent and moisturizing agents, which makes the surfaces to which it is applied repellent to stains, preventing dirt from adhering strongly or penetrate by capillary action.
      • In this way, the treated surfaces are protected by a totally invisible, highly durable barrier that allows the material to "breathe" without changing the colour or gloss of the surface, while preventing the surface from absorbing: oils, greases, sauces, coffee and other beverages, facilitating its cleaning and maintaining its original appearance for long periods of time without requiring any special maintenance to preserve its properties.
      • Its water-based formula makes it odourless and safe for the operator and end-user. Thanks to this characteristic, it is suitable for indoor and outdoor application on all types of absorbent surfaces, both natural and synthetic. It can also be applied even to surfaces that contain a high moisture content, such as after a thorough cleaning. This peculiarity allows optimising the application costs, since it is not necessary for the surface to be completely dry, as is the case with equivalent products containing organic solvents.
      • It also has water-repellent properties, for which the protective barrier also slows water absorption. This characteristic reduces problems caused by water, such as formation of salts and white efflorescence, appearance of rust stains, moulds, etc.
     

    Application Areas

    Stone Aquo Protector is suitable to be applied on all types of absorbent surfaces where oil-repellent and anti-stain properties are desired. For example:
    • Marble.
    • Granite.
    • Terrazzo.
    • Limestone.
    • Concrete.
    • Microcement.
    • Etc.

    Mode of Application

    1. Stone Aquo Protector is a ready to use product, therefore it does not need to be diluted before use. Before applying the product the surface must be clean and preferably dry or with a humidity level not exceeding 40%.
    2.  Then apply the product with a brush, roller or spray, spreading it evenly over the entire surface until the product is properly saturated. In very porous materials it is recommended to apply two layers “wet on wet”, with a maximum of 60 minutes between each application.
    3.  Finally, let the product work for a few hours until it is completely absorbed. The surface will be fully protected within 24 hours of its application. If the application of the product has been excessive regarding the absorbent characteristics of the surface, the excess must be removed using a cloth slightly dampened with the product within 30-40 minutes. The tools can be rinsed with water after use. For maintenance cleaning of the protected surfaces, use a pH neutral cleaner-degreaser.

    Format

    • Plastic containers of 1, 5, 10 and 30 litres.
    Details
  • PROTECTOR STONE PLUS

    Stone Plus Protector is an easy to use natural effect stain protector designed for the protection of absorbent surfaces, for indoor and outdoor use, formulated from solvent based organosilicon and fluoropolymers derivatives. The treated surfaces acquire a water-repellent and oil-repellent protection, preventing them from absorbing water, as well as oils and greases. As a result, the fouling tendency is reduced, increasing the ease of cleaning and thus reducing maintenance costs. These special qualities make the product ideal to protect those materials that are frequently used and that must remain in optimum condition during their service life, such as kitchen worktops, marble or granite tables, restaurant floors, façades, etc. The generated colourless protective barrier repels water, efflorescence, and humidity by combining the stain protection with the water-repellent action. In addition, its high concentration of active ingredient protects against the most penetrating and difficult to remove stains such as: grease, cooking oils, ketchup, coffee, etc. It does not generate a film on the surface, but reacts chemically with the surface, giving it the properties mentioned above. This allows water vapour and atmospheric gases to pass through, for which its application does not alter the surface perspiration and therefore, does not cause condensation problems like other film-forming products.   Application Areas It can be applied on all types of absorbent surfaces to which water and oil repellent properties want to be added. It can be applied to marble, granite, limestone, terrazzo, natural stone, concrete, terracotta, ceramic materials, etc.

    Mode of Application

    1. Stone Aquo Protector is a ready to use product, therefore it does notneed to be diluted before use. Before applying the product, make sure that the surface is absorbent, it is completely clean, dry and without poorly adhered debris.
    2. Then apply the product with a brush, a short haired roller or a cloth and spread it evenly over the entire surface until the surface is properly saturated. The best results are obtained when two wet-on-wet layers are applied. (For highly absorbent and porous materials, it may be necessary to apply one or two additional layers to achieve total saturation of the same.)
    3. Then let the surface absorb the treatment. If the application of the product has been excessive regarding the absorbent characteristics of the surface, the excess must be removed using a cloth slightly dampened with the product within no more than 30-40 minutes.
    4. Finally, let the product react with the surface for a few hours. The total reaction of the product occurs 24 hours after application.
    5. For maintenance cleaning of the protected surfaces, use a neutral cleaner.

    Format

    • Metal containers of 5, 10 and 25 litres.
    Details
  • SELLACRIL IMPRESO sellacrill impreso neoquim

    SELLACRIL IMPRESO

    Sealant and protector for printed pavement. Solvent base.
    • Increases mechanical strength.
    • Excellent protection and gloss.
    • Reduces the tendency to fouling.
    • Improves and restores the original colour.
    • Slows down cracking.
    • Provides wet effect.
    Sellacril Impreso is a transparent and colourless varnish, based on high strength acrylic resins, developed to seal and protect all types of concrete or printed concrete surfaces. Sellacril Impreso, after its application generates a colourless high gloss surface film, which increases the mechanical strength of the pavement, while restoring and improving its tone, reduces the fouling tendency and eliminates dust generation. The high quality of the polymers used in its formulation, together with the solvents used and their low viscosity, allows Sellacril Impreso to have a high penetration capacity on the pavement. In this way, the product enters the pavement pores, chemically anchoring itself to the aggregates and cementitious components, reinforcing its internal structure and compacting the material. Sellacril Impreso is suitable for both indoor and outdoor application on moderate to high absorption capacity surfaces, whether vertical or horizontal.

    Application Areas

    Sellacril Impreso is suitable for use on all types of concrete, stone or brick surfaces in general, especially for all types of absorbent surfaces where a glossy finish, protection and increased mechanical strength are desired. It can therefore be used in:
    • Printed concrete floors.
    • Polished concrete.
    • Masonry.
    • Etc.

    Mode of Application

    Sellacril Impreso is a ready to use product, so it does not need to be diluted before applying. Before applying Sellacril Impreso, make sure that the surface is clean, dry, free of greases, oils, crumbly particles, etc. and, in short, free of any contaminants that may reduce the adhesion capacity of the product. Also, the surface must have a residual humidity of less than 4%. Then, apply Sellacril Impreso using a brush, a roller or an airless sprayer, ensuring the generation of a uniform layer and a correct overlap between panels. It is not recommended to apply layers with a thickness greater than 150 um wet. Finally, let the product dry. (For indoors, it is recommended to maintain the maximum possible ventilation, to facilitate drying.)

    Format

    • Metal container of 5 litres.
    • Plastic containers of 30 and 60 litres.
    Details
  • Resina de puente y unión NEOCEM NQ

    NEOCEM NQ

    • Excellent adhesion.
    • Moisture resistant.
    • Extra-high tack.
    • Excellent open working time.
    • Not flammable or dangerous.

    Description

    Neocem NQ is a ready-to-use, high tack, water-based, self-adhesive primer formulated with 100% acrylic resins of very high quality, specially developed to increase the adhesion of cementitious materials and water-based plastic paints on difficult-to-bond surfaces, such as very smooth and/or low porosity surfaces, on both vertical and horizontal surfaces. Neocem NQ has excellent resistance to moisture and alkalis, maintaining its adhesive properties throughout its service life and, unlike other primers, retains a good degree of adherence and elasticity over time. These characteristics allow Neocem NQ to have an excellent open working time: from 15 minutes to several days*, optimizing operations on site and reducing the time required for the same. Neocem NQ is not flammable or hazardous to the environment or the operator, for which its use is completely safe and validated by the OSH departments. It is also water vapour breathable, it is suitable for application with residual moisture in the surface (< 7%) and from 0 oC.. Thanks to these properties, Neocem NQ can be used on surfaces such as: mortar, plaster, brick, fibre cement, wood or natural stone, among others, and in all kinds of works: partition walls with columns, bonding of new mortar with old mortar, mortar screeds, tiled, etc.

    Application Areas

    Neocem NQ can be used on all types of materials commonly used in constructions that do not have zero absorption.

    Mode of Application

    Neocem NQ is a ready to use product, so it must be applied as it is supplied. It should not be diluted under any circumstances, since its adhesive characteristics will be diminished. In addition, Neocem NQ should be applied on cohesive surfaces, with low residual humidity (<4% preferably), completely set and completely clean of dirt such as: dust, rust, efflorescence, stripping substances and, in short, free of any substance that hinders or nullifies the adhesion of the acrylic resins. Once you have verified that the surface meets the above characteristics:
    1.  Apply the product on the surface using a brush, a roller or an airless sprayer.
    2.  After 15 minutes of its application, carry out the required work on the site

    Format

    • Plastic containers of 1, 5, 10 and 60 litres.
    Details
  • PROTECTOR STONE

      Anti-stain protector for porous surfaces. Stone protector is a natural effect stain protector that prevents the capillary penetration of oils, greases, sauces or food products residues, mineral oil... Its high concentration of active ingredient protects against the most penetrating and difficult to remove stains such as: grease, cooking oils, ketchup, coffee, etc. The treated surfaces acquire an oil-repellent protection, preventing the appearance of oil and grease stains. These special qualities make the product ideal to protect those materials that are frequently used and that must remain in optimum condition during their service life, such as kitchen worktops, marble or granite tables, restaurant floors, façades, etc.  

    Application Areas

      For all types of absorbent surfaces to which oil repellent properties want to be added:
    • Marble.
    • Granite.
    • Terrazzo.
    • Natural stone.
    • Synthetic stone.
    • Concrete.
    • Clay.
    • Ceramic.

    Mode of Application

      Before applying the product, the surface must be clean and dry.
    1. Apply the product with a brush, a short haired roller or a cloth and spread it evenly over the entire surface until the same is properly saturated.
    2. For very porous materials is recommended to apply two wet-on-wet layers, with a maximum of 60 minutes between each application.
    3. Let the product react with the surface for a few hours. The surface will be fully protected within 24 hours of its application.
    Stone Protector is a ready to use product, therefore it does not need to be diluted before use. Para materiales muy porosos, aplicar 2 o 3 capas, dejando 30/60 minutos entre cada aplicación. If the application of the product has been excessive regarding the absorbent characteristics of the surface, the excess must be removed using a cloth slightly dampened with the product within 30-40 minutes.

    Format

    • Metallic containers of 0.5 L, 1, 5, 10 and 50 litres.
    Details
  • HYDROSOL 10

    Water repellent for façades and low porous surfaces.
    • Invisible finish.
    • Product ready to use.
    • Quick drying.
    • Specific for low to very low absorption surfaces.
    Ver video-demo Hidrosol 10 is a colourless, solvent-based, ready to use, natural finish water repellent, suitable for all types of vertical and horizontal low-porous surfaces, such as façades and exterior walls of polished mortar and cement, stone, brick, plaster, prefabricated plasters or silicate paints, among others. This treatment forms a completely invisible protective barrier that repels water of all types of low-absorption building materials, without forming a film or changing the appearance of the surface, neither yellowing nor cracking over time. The treated surface is provided with a remarkable resistance against atmospheric agents avoiding the damage that can be caused by rain: humidity, mould, verdigris, as well as the appearance of saline efflorescences and humidity spots by capillarity.

    Application Areas

    Hidrosol 10 can be applied to all types of construction materials:
    • Façades, roofs and terraces of natural or artificial stone, concrete, fibro-cement, caravista brick, plaster, slate, terracotta, alkaline surfaces or not.

    Mode of Application

    Hidrosol 10 is a ready to use product, requiring no dilution before its use. Ensure that the surface to be treated is completely dry, free of dust, dirt, oils, efflorescence and at a temperature between 5 and 35 °C. If there are unsealed joints or cracks, repair the surface. Then apply Hidrosol 10 using an airless sprayer, low pressure sprayer, brush or roller, applying two layers of the product following the wet on wet methodology. That is to say, apply a first Hidrosol 10 coat and then apply the second coat of the product while the first is still humid, let it react and wait for it to dry IMPORTANT: Apply the product in a period without rainfall. If rain is likely to occur within 24 hours of the application, the treatment must be protected to prevent a premature deterioration.

    Format

    • Metal containers of 1, 5, 10 and 60 litres.
    Details
  • IMPERLATEX PU INCOLORO

    Transparent water-proofing based on aliphatic polyurethane.
    • Excellent durability.
    • High cracking resistance.
    • Completely transparent and colourless.
    • Optimum outdoor resistance.
    •  Monocomponent.
    Imperlatex PU Incoloro is a low viscosity waterproofing nanocomponent, transparent and solvent based, based on 100% aliphatic polyurethane resin of high gloss and durability, designed to waterproof all types of vertical or horizontal surfaces, both indoors and outdoors. Once applied, it generates a totally continuous water-resistant membrane with excellent adhesion and optimal elasticity.

     In addition, it has the following characteristics:

    •  Absolute waterproofing, resisting even permanent contact, being suitable for waterproofing planters or ornamental fountains.
    •  Hydrolysis and solar radiation resistance, strongly recommended for outdoor use.
    • Resistant to microorganisms and bacteria attack, not degraded by the action of the latter in shady areas.
    •  Permeable to water vapour, allows the surface to breathe, its use does not cause condensation problems.
    • Total resistance to detergents, household cleaners and acid rain.
    • Optimal adhesion on all types of absorbent surfaces.
    • Controlled elasticity, allowing transit without risk of breakage or cracking.
    • Excellent abrasion resistance.
    • High filling capacity of cracks, joints and pores. Its low viscosity formulation allows the product to penetrate the cracks, joints and pores filling them completely.

    Application Areas

    Especially recommended for carrying out all types of waterproofing work where a completely transparent product is desired. These qualities make it suitable for use on decks, terraces, rooftops, walls, planters, etc.

    Mode of Application

    Being a ready to use product, it does not need to be diluted before applying. The use of solvents can dramatically reduce membrane adhesion and durability. The surface must be completely clean, dry, hardened and free from other membranes or contaminants that can reduce the service life of the membrane, such as dust, moss or salt efflorescence. It is also recommended that the surface does not contain cracks or holes greater than 1 mm. In low/no absorption surfaces it is recommended to perform and adhesion-promoting treatment using Microprimer.

    The following procedure is recommended:

     
    a). Absorbent surfaces, (burnt clay, rustic tile, Catalan tile.. etc.):
    1.  Thoroughly clean the surface. Select the type of cleaner according to the existing dirt: (Limfa for efflorescence, moss and verdigris, Neogras Forte for oil stains or pollution).
    2.  Allow the surface to dry completely and fill/repair damage such as joints, cracks or holes.
    3. Apply a first layer dissolved in Disol (3 parts Imperlatex PU Incoloro: 1 part Disol), using a short hair roller, brush or airless sprayer
    4.  Allow to dry for 6-8 hours and apply a second coat to obtain the desired yield and thickness.
    5.  Allow the product to dry until it is completely cross-linked. (The drying process is dependent on ambient humidity and temperature. It is recommended to protect the application from the weather and condensation during the first 24-36 hours). The membrane acquires its maximum resistance 7 days after application. During this time it is recommended not to wet it or walk on the same.
    b). Non-absorbent surface, (glazed ceramics, porcelain tiles, polished stone… etc.):
    1. Thoroughly clean the surface. Select the type of cleaner according to the existing dirt: (Limfa for efflorescence, moss and verdigris, Neogras Forte for oil stains or pollution).
    2. Allow the surface to dry completely and fill/repair damage such as joints, cracks or holes.
    3.  Prime the surface with Microprimer at about 40-50 m2 /L and allow to dry for a maximum of 15-30 minutes.
    4. Apply two coats, using a short hair roller, brush or airless sprayer, allowing 6-8 hours drying time between coats.
    5. Allow the product to dry until it is completely cross-linked. (The drying process is dependent on ambient humidity and temperature. It is recommended to protect the application from the weather and condensation during the first 24-36 hours). The membrane acquires its maximum resistance 7 days after application. During this time it is recommended not to wet it or walk on the same.

    Format

    • Metal containers of 1, 5, 10 and 25 kg.
    Details