• HIDROSOL AQUO PLUS

    Colourless water based water-repellent with for

    HIDROSOL AQUO PLUS

    Colourless water based water-repellent with for.
    • Water based.
    • High water repellent power.
    • It does not alter the tone.
    •  Reduces dirt adhesion.
    •  Vapour breathable.
    Hidrosol Aquo Plus is a water resistant product ready to use for façades made of concrete, mortar, masonry, brick, natural stone or fibre cement, among others, formulated with organosilic compounds of the latest technology, emulsified in water. hanks to its high concentration of active ingredients, Hidrosol Aquo Plus provides a high water-repellent capacity and an optimal pearl effect, without altering the original tone of the surface or forming a film. It prevents water penetration into the surface while allowing its breathability and reduces the formation of efflorescence, moss and lichens, maintaining the aesthetic conditions of the wall finish. Hidrosol Aquo Plus can be applied both indoors and outdoors since it does not emit any solvent/odour and is totally UV resistant.

    Application Areas

    This product is especially suitable for water-proofing all types of vertical construction surfaces or on surfaces with slopes of more than 5 degrees of inclination, such as: Natural stone, caravista brick, concrete, mortar, plaster, fibre cement, roof tile…

    Mode of Application

    Before applying Hidrosol Aquo Plus, it must be checked that the surface is fully hardened and set in case of new constructions, totally dry, free of dust, dirt, oils, efflorescence and a temperature between 5 and 35 °C It can be applied with an airless sprayer, brush or roller, applying two layers of product using the “wet on wet” methodology. To do this, apply the second layer of product while the first layer is still humid. Hidrosol Aquo Plus is not suitable for horizontal surfaces, nor for being coated with cement or lime based paints.

    Format

    • Plastic containers of 1, 5, 10 and 30 litres.
    WATCH VIDEO.
    Details
  • NEOQUIM - HIDROSOL MG

    Wet look water repellent for low porous surfaces.

    HIDROSOL MG

    Wet look water repellent for low porous surfaces.
    • Protects against problems caused by water.
    • It enhances the tone of the stone.
    • Improves wear resistance.
    • Allows the surface to breathe.
    • Ready to use.
    Hidrosol mg is a water-repellent product, based on siloxanes and polysiloxanes in a solvent base, specifically created to protect all types of absorbent surfaces against problems caused by water, such as humidity, salt efflorescence, moulds and verdigris growth or the appearance of frost cracks, among others. In addition, Hidrosol MG positively contributes to reduce the heat transmission coefficient of the treated wall, improving its thermal insulation capabilities. Its well thought out resin-free composition provides a completely colourless and non-gloss water barrier, keeping the surface breathability intact. Once the product has been absorbed by the surface, Hidrosol MG enhances its natural tone, giving it a moist appearance. This gives the surfaces a completely rejuvenated appearance with more vivid colours. Hidrosol MG is suitable for all types of materials and absorbent surfaces, both vertical and horizontal with a slight slope (>3%), which together with its optimal resistance to abrasion and UV rays, has excellent durability. In addition, since it does not contain any resins in its composition, it does not yellow, crack or peel over time and is 100% trafficable.

    Application Areas

    Hidrosol mg is the ideal product to use when it is necessary to protect low porosity surfaces against the action of water and give them a wet appearance simultaneously. For example: polished marble and granite surfaces, slate, unglazed ceramic surfaces…etc.

    Mode of Application

    HYDROSOL MG is a ready to use product, so it does not need to be diluted before applying. Before applying Hidrosol MG, the surface must be completely clean, hardened and perfectly dry. In addition, it must be absorbent, otherwise the treatment will not be effective, generating a sticky surface. Then apply Hydrosol MG on the surface until it is fully saturated. This can be done by using: short hair roller, brush or low pressure spray. Then, let the product be absorbed by the treated stone for 30 minutes. If after that time Hydrosol MG has not completely penetrated, remove the excess with the help of a cloth / absorbent material. Finally, let the treatment dry completely. After 24 hours the product is 100% effective. It is recommended to protect against condensation or rain within the first 24 hours of application.

    Format

    • Metal containers of 1, 5, and 10 litres.
    • Plastic container of 30 litres.
    Details
  • HIDROSOL STONE PLUS BLACK

    Water repellent – colour enhancer for granites and black marbles.

    HIDROSOL STONE PLUS BLACK

    Water repellent – colour enhancer for granites and black marbles.
    • High concentration
    • Intensifies and restores the original black colour of the stone.
    • Optimal water-repellent protection.
    •  Excellent durability.
    Hidrosol Stone Plus Black is a solvent based water repellent based on siloxanes and polysiloxanes specifically designed to be applied on black marble and granite surfaces.

    Hidrosol Stone Plus Black has a dual mode of action:

    1.  It provides hydrophobic properties to the surfaces where it is applied. In this manner, the treated stone does not absorb water, reducing the problems caused by the same such as: appearance of white spots, saline efflorescence, loss of gloss, oxidation… etc. This mode of action is obtained thanks to its silicon-based compounds, high hydrophobic capacity and excellent resistance to wear and light.
    2. It intensifies and restores the original black colour of the stone, giving it a high durability deep black hue that conceals small imperfections or streaks in granites and marbles bringing back their original appearance. Its extremely fine pigments penetrate the stone and improve the visual characteristics of the surface thanks to their high opacity.
    Hidrosol Stone Plus Black does not use resins or polymers in its composition, so it acts without altering the surface gloss. This fact makes it especially useful on surfaces with honed or flamed finishes.

    Application Areas

    Hidrosol Stone Plus Black is suitable to be applied in all types of natural black stone, both vertical and horizontal, such as:
    • Floors.
    • Countertops or tables
    • Decorative elements
    • Etc.

    Mode of Application

    Hidrosol Stone Plus Black is a ready to use product, so it does not need to be diluted before its application. Before applying Hidrosol Stone Plus Black, the surface must be completely clean, hardened and perfectly dry. In addition, it must be absorbent, otherwise the treatment will not be effective, generating a sticky surface. Apply Stone Plus Black on the surface until it is fully saturated. It can be applied with: a short hair roller, brush or low pressure spray, it is recommended to apply it following the “wet on wet” technique in two crossed layers. Then, let the product be absorbed by the stone for 30 minutes. If after said time Hidrosol Stone Plus Black has not completely penetrated, remove the excess with the help of a cloth / absorbent material, rubbing gently with circular movements Finally, let the treatment dry completely. After 24 hours the product is 100% effective.

    Format

    • Metal containers of 0.5 litres+box, 1, 5 and 10 litres.
    • Plastic container of 30 litres.
    Details
  • NEOQUIM - HIDROSOL STONE PLUS

    Brightener, protective and water repellent for synthetic materials.

    HIDROSOL STONE PLUS

    Brightener, protective and water repellent for synthetic materials.
    • Protects against water.
    • Improves gloss and enhances the colour.
    • For quartz and non-absorbent synthetics.
    • Makes cleaning easy.
    Hidrosol Stone Plus is a brightener, protector and colour intensifier specially developed for non-absorbent surfaces such as synthetics, quartz agglomerates or natural non-porous or highly polished stone. It is based on non-toxic wetting agents, solvents and non-toxic colour enhancers and protectants. Hidrosol Stone Plus, boosts the gloss and enhances the natural colour of the treated surfaces after its application, generating a thin film that is completely transparent and colourless providing high protection against water stains. Treated surfaces also have a soft feel and are easier to clean. Thanks to these features, Hidrosol Stone Plus is the most recommended product to be used in cases where a typical water repellent (designed for absorbent surfaces) cannot be used. Suitable for both professional and home use. Hidrosol Stone Plus can be used by all types of users for its ease of use. Hidrosol Stone Plus can be applied regularly to keep the surface gloss intact.

    Application Areas

    Hidrosol Stone Plus is intended to provide protection, enhance the tone and increase the gloss of non-absorbent and/or polished surfaces, such as technological quartz, marble, granite, glazed ceramics, among others, on all types of surfaces and uses:
    • kitchen and bathroom worktops,.
    • Tables.
    • Decorative elements,.
    • Bar tops in businesses,.
    • Vertical claddings,.
    • Etc.

    Mode of Application

    Hidrosol Stone Plus is a ready to use product, so it does not need to be diluted before its application. Before applying, the surface must be clean and completely dry.

    Then:

    1. Moisten a microfibre cloth with Hidrosol Stone Plus.
    2. Spread the product evenly over the entire surface to be treated.
    3. Leave it on for 10- 15 minutes.
    4. Remove excess product with a dry microfibre cloth.
    5. Rub the surface, preferably with circular movements, until the desired gloss is obtained.

    Format

    • Metal containers of 0.5 litres+box, 1, 5 and 10 litres.
    • Plastic container of 30 litres.
    Details

  • Water repellent for façades and low porous surfaces.

    HYDROSOL 10

    Water repellent for façades and low porous surfaces.
    • Invisible finish.
    • Product ready to use.
    • Quick drying.
    • Specific for low to very low absorption surfaces.
    Ver video-demo Hidrosol 10 is a colourless, solvent-based, ready to use, natural finish water repellent, suitable for all types of vertical and horizontal low-porous surfaces, such as façades and exterior walls of polished mortar and cement, stone, brick, plaster, prefabricated plasters or silicate paints, among others. This treatment forms a completely invisible protective barrier that repels water of all types of low-absorption building materials, without forming a film or changing the appearance of the surface, neither yellowing nor cracking over time. The treated surface is provided with a remarkable resistance against atmospheric agents avoiding the damage that can be caused by rain: humidity, mould, verdigris, as well as the appearance of saline efflorescences and humidity spots by capillarity.

    Application Areas

    Hidrosol 10 can be applied to all types of construction materials:
    • Façades, roofs and terraces of natural or artificial stone, concrete, fibro-cement, caravista brick, plaster, slate, terracotta, alkaline surfaces or not.

    Mode of Application

    Hidrosol 10 is a ready to use product, requiring no dilution before its use. Ensure that the surface to be treated is completely dry, free of dust, dirt, oils, efflorescence and at a temperature between 5 and 35 °C. If there are unsealed joints or cracks, repair the surface. Then apply Hidrosol 10 using an airless sprayer, low pressure sprayer, brush or roller, applying two layers of the product following the wet on wet methodology. That is to say, apply a first Hidrosol 10 coat and then apply the second coat of the product while the first is still humid, let it react and wait for it to dry IMPORTANT: Apply the product in a period without rainfall. If rain is likely to occur within 24 hours of the application, the treatment must be protected to prevent a premature deterioration.

    Format

    • Metal containers of 1, 5, 10 and 60 litres.
    Details

QUICK ACCESS

Legal warning
Cookies policy
Privacy policy

Subscribe to our newsletter

SUBSCRIBE

CONTACT

Phone no: +34 968 687 839
E-Mail: neoquim@neoquim.com
Address: P.I. de Lorquí C/Archena, Nave 23 C.P: 30564 Lorquí (MURCIA)